2013 - 2018 Cummins
In 2013 Ram went to a two filter setup with the primary fuel/water separator being chassis mounted above and forward of the rear axle and the secondary fuel filter still being up front in the canister on the left side of the engine block. If you buy the recommended brands of filters, you now get better filtration than prior models, however, now the issue is the combined cost of these two filters. These recommended filters cost anywhere between $125-175 to replace at a recommended 15,000 mile interval if you do it yourself. After making many phone calls around the country, dealers are getting upwards of $350 just to change the fuel filters on these trucks. Ridiculous!
​
We have not only come up with a solution for the high cost, we have also made it very simple for guys that would normally take it into the dealership, to do themselves in under 10 minutes easily saving them a couple hundred dollars every 15,000 miles.
​
Why We Put Fleetguard Filters In Our Kits
We developed these kits years ago to give guys the BEST protection they could get for their trucks at an affordable price. We also wanted guys to be able to get filters in there local hometown, rather than buying them from us like other companies do. We had the CAT 1R-0750 filter in our kits for over 10 years, because they are a great filter and are readily available. Now the CAT filters are considered an older filter-media technology compared to the advancement in filtration over the last several years. We have also seen fake knockoffs out there in the marketplace that can cause issues and leave you less protected. Our goal will always be to provide you with the BEST filtration you can get, to protect your high-dollar investment. Introducing the NanoNet technology!
The newer NanoNet technology found in Fleetguard fuel filters is now the most up to date, advanced technology and superior protection you can buy. The result of this Nanonet technology gives it a 2 micron rating at over 99.6% efficiency! Do your own research on these Fleetguard Nanonet filters. For the low cost and the easy availability, you will be pressed to find a better filter out there to protect your truck.
With Our Kits We Give You:
- Better than stock filtration for added protection.
- Very affordable filter changes that are completed in minutes without even opening the hood.
- Easy 45 minute installation with absolutely no drilling or cutting of anything.
- Completely reversible back to stock in minutes.
​
Our Kit And How It Will Save You Money
Because of the new fuel system design starting in 2013 we wanted to retain the stock rear water-separator having the heating element and WIF (water in fuel) sensor. With our kit we add the Fleetguard FF5814 NanoNet filter right beside it to give you the best filtration you can possibly have, all at the rear of the truck in one easy to get to location. Once our kit is installed, you will have two options with the forward filter under the hood. You can leave it in place and change it every 2-3 years because of algae growth that will appear on it over time from todays increasingly bad fuel, or completely get rid of it using our Delete Kit below. This option removes everything related to the filter and really cleans up the engine bay.
​
You can purchase the basic '13-18 Cummins Kit which comes with the Fleetguard FF5814 NanoNet filter alone, or you can also add a Fleetguard FS20089 water-separator (replaces your stock water Separator filter) to get you reset for another 15,000 miles. These filters are readily available in any decent size town, or you can order them online or through our Filters & Parts page.
With our kit installed, you will only spend approximately $80 per filter change saving around 50%. This cost will change both rear filters at 15,000 mile intervals.
2013 - 2018 Cummins Filter Kit
Our '13-18 Cummins Filter Kit installs right beside the stock filter location at the rear of the truck. It is a simple install of around 45 minutes.
​
This kit provides the highest level of protection available for your engine with the newest NanoNet technology filter design.
Want to see the easy install instructions before purchasing? Click here.
Please Note: This kit was designed and manufactured for the 2013-2018 Ram Cummins 6.7 diesel 2500 & 3500 non cab-chassis trucks. This filter kit mounts towards the rear of the truck underneath beside the stock water-separator filter. If your fuel tank is between the frame rails at the very back end where a spare tire would normally mount, this is a cab-chassis style and this kit will not fit. Returns are accepted within 30 days of purchase with a 15% restocking fee and our actual shipping charges taken out. All returns must be approved by phone and in resalable condition which means mounting bracket not scratched, parts clean and the plastic still on the filters.
​
Optional Cold Weather Sleeve
Also available is the Cold Weather Sleeve. Coming directly after the heated primary filter this is sure to help in really cold climate areas. Although we have not had any issues with our other kits, it is something guys ask about with a 2-micron filter. Being proactive, rather than reactive, with a good anti-gelling additive is just part of being a responsible diesel owner in really cold climates. These Weather Sleeves can be found over on our Filters & Parts page.
​
You can also add the popular Fleetguard FS20089 filter to the kit to replace your rear stock water filter when installing our kit. This will get you completely reset for another 15,000 miles.
​
'13-'18 Cummins 6.7 Filter Kit
2013-2018 2500 & 3500 MODELS
(Does not fit Cab-Chassis models)
Basic Filter Kit
(If you want to delete your under-hood filter, order kit down below under Delete Kit)
$185.00
($5 Flat-Shipping)
* USPS Priority 2-3 day shipping in the US with tracking *
Choose Kit Type by Clicking Box Below:
All orders will be processed through Throttle-Up Industries LLC
​
Click here for the Frequently Asked Questions page.
​
If ordering by phone is preferred instead, please call 541-678-7827
2013.5 - 2018 Stock Filter Delete Kit
Our hose gives you 25% more fuel flow to the CP3 over stock.
Please Note: This kit will completely delete the under-hood fuel filter canister on the side of your block on the 2013.5-2018 trucks (we are finding a lot of the early '13 trucks still have the '12 fuel line setup which will not work with this quick-disconnect hose). What the companies that sell these delete blocks don't tell you when you buy from them, is that once you install the delete block, you than have to go out and have a special hose made up to go from your fuel supply line down on the frame rail up to your CP3 injection pump since you are eliminating the fuel filter housing. These delete blocks only take care of the return fuel back to the tank and the stock WIF sensor. This kit includes both the delete block and the fuel line you need to get the job done. In fact......we can go a step further and say that we are getting 25% more fuel volume up to the injection pump by the size of our hose and quick-disconnect fittings we use compared to the stock parts.
​
Want to see the easy install instructions before purchasing? Click here.
2013.5 - 2018 Stock Filter Delete Kit
$134.00
($5 Flat-Shipping)
* USPS Priority 2-3 day shipping in the US with tracking *
Add Filter Kit by Clicking Box Below:
All orders will be processed through Throttle-Up Industries LLC
​
Click here for the Frequently Asked Questions page.
​
If ordering by phone is preferred instead, please call 541-678-7827