2019 - Present Cummins
In 2019 Ram went from the spin-on water separator filter in the rear, to a cartridge style filter canister mounted above and forward of the rear axle and the secondary fuel filter still being up front on the left side of the engine block. They also went to the troublesome CP4 for some reason on the '19-20's, going back to the CP3 in '21. These CP4's plagued Duramax from 2011-2016 and all the newer Powerstrokes. The CP4's are very sensitive to bad fuel and definitely need better filtration and lubricity to stay protected. If you buy the recommended filters, you get better filtration than the earlier trucks had to protect your fuel system, however now the issue is the combined cost of these two filters to replace. These recommended filters cost anywhere between $125-175 to replace at a recommended 15,000 mile interval if you do it yourself. After making many phone calls around the country, dealers are getting upwards of $350 just to change the fuel filters on these trucks. Ridiculous!
​
We have not only come up with a solution for the high cost, we have also made it very simple for guys that would normally take it into the dealership, to do themselves in under 10 minutes. Easily saving them a couple hundred dollars every 15,000 miles.
Why We Put Fleetguard Filters In Our Kits
We developed these kits years ago to give guys the BEST protection they could get for their trucks at an affordable price. We also wanted guys to be able to get filters in there local hometown, rather than buying them from us like other companies do. We had the CAT 1R-0750 filter in our kits for over 10 years, because they are a great filter and are readily available. Now the CAT filters are considered an older filter-media technology compared to the advancement in filtration over the last several years. We have also seen fake knockoffs out there in the marketplace that can cause issues and leave you less protected. Our goal will always be to provide you with the BEST filtration you can get, to protect your high-dollar investment. Introducing the NanoNet technology!
The newer NanoNet technology found in Fleetguard fuel filters is now the most up to date, advanced technology and superior protection you can buy. The result of this Nanonet technology gives it a 2 micron rating at over 99.6% efficiency! Do your own research on these Fleetguard Nanonet filters. For the low cost and the easy availability, you will be pressed to find a better filter out there to protect your truck..
​
With Our Kit We Give You:
- Better than stock filtration for added protection.
- Very affordable filter changes that are completed in minutes without even opening the hood.
- Easy 45 minute installation with absolutely no drilling or cutting of anything.
- Completely reversible back to stock in minutes.
Our Kit And How It Will Save You Money
Because of the new fuel system design starting in 2013 we wanted to retain the stock rear water-separator having the heating element and WIF (water in fuel) sensor. With our kit we add the Fleetguard FF5814 NanoNet filter right beside it to give you the best filtration you can possibly have, all at the rear of the truck in an easy to get to location. Once our kit is installed, you will only need to change the forward filter under the hood every 2-3 years because of algae growth that will appear on it over time from todays increasingly bad fuel.
​
You can purchase the Basic 19-Present Cummins kit which comes with theFleetguard FF5814 NanoNet filter alone,or you can also add a Baldwin water-separator (replaces your stock water Separator filter) to get you reset for another 15,000 miles. These filters are readily available in any decent size town, or you can order them online or through our Filters & Parts page.
With our kit installed, you will only spend approximately $80 per filter change saving around 50%. This cost will change both rear filters at 15,000 mile intervals.
Easy Installation, But Even Easier Removal
This fuel filter kit was designed to be initially installed in 45 minutes, but to then be completely removed in only 10 minutes should you want to pull it for any warranty work you may need done to be completely untraceable at the dealer. Most dealerships have absolutely no problem with added fuel filtration. This kit utilizes the stock, push-button quick disconnect fuel fittings for an easy installation and removal.
2019-Present Cummins Filter Kit
Our '19-Present Cummins Filter Kit installs right beside the stock water filter location at the rear of the truck. It is a simple install of around 45 minutes.
​
This kit provides the highest level of protection available for your engine with the newest NanoNet technology filter design.
Want to see the easy install instructions before purchasing? Click here.
Please Note: These '19-Present Cummins Filter Kits were designed and manufactured for the 2019-Present Ram Cummins 6.7 diesel 2500 & 3500 non cab-chassis trucks. This filter kit mounts towards the rear of the truck underneath beside the stock water-separator filter. If your fuel tank is between the frame rails at the very back end where a spare tire would normally mount, this is a cab-chassis style and this kit will not fit. Returns are accepted within 30 days of purchase with a 15% restocking fee and our actual shipping charges taken out. All returns must be approved by phone and in resalable condition which means mounting bracket not scratched, parts clean and the plastic still on the filters..
Optional Cold Weather Sleeve
Also available is the Cold Weather Sleeve. Coming directly after the heated primary filter this is sure to help in really cold climate areas. Although we have not had any issues with our other kits, it is something guys ask about with a 2-micron filter. Being proactive, rather than reactive, with a good anti-gelling additive is just part of being a responsible diesel owner in really cold climates. These Weather Sleeves can be found over on our Filters & Parts page.
​
You can also add the popular Baldwin PF46152 filter to the kit to replace your rear stock water filter when installing our kit. This will get you completely reset for another 15,000 miles.
(Unfortunately Fleetguard doesn't make one yet.)
19-Present Cummins Filter Kit
19-Present 2500 & 3500 Models
(Does not fit Cab-Chassis models)
Basic Filter Kit
$194.00
($5 Flat-Shipping)
* USPS Priority 2-3 day shipping in the US with tracking *
Choose Kit Type by Clicking Box Below:
All orders will be processed through Throttle-Up Industries LLC
​
Click here for the Frequently Asked Questions page.
​
If ordering by phone is preferred instead, please call 541-678-7827